Percorrer por autor "Carvalho, G. H. S. F. L."
A mostrar 1 - 4 de 4
Resultados por página
Opções de ordenação
- Friction stir welding and explosive welding of aluminum/copper: process analysisPublication . Carvalho, G. H. S. F. L.; Galvão, I.; Mendes, R.; Leal, R. M.; Loureiro, A.The 6082 aluminum alloy was welded to copper-DHP by friction stir welding and explosive welding. The effect of each welding process on the microstructural evolution, the intermetallic phases distribution, and the mechanical behavior of both types of welds was analyzed and compared. The microstructural changes proved to be much more expressive in friction stir welding due to the larger area under plastic deformation, the stirring and mixing of the alloys, the longer time under high temperature, and the longer interaction times between the base materials during welding. As explosive welding process is much faster, it avoids extensive microstructural changes and significant interaction of the materials, reducing the intermetallic volumes and their distribution along the interface. The friction stir welds presented Cu-rich intermetallics while the explosive welds presented Al-rich intermetallics. For alloys that can easily form brittle intermetallic phases, excessive interaction during the welding process leads to a very poor mechanical behavior of the joints.
- Influence of base material properties on copper and aluminium–copper explosive weldsPublication . Carvalho, G. H. S. F. L.; Galvão, I.; Mendes, R.; Leal, Rui; Loureiro, A.The influence of base material properties on the interfacial phenomena in copper and aluminium–copper explosive welds was studied. Two explosive mixtures with different detonation velocities were tested. Sound aluminium–copper joints with effective bonding were achieved by using an explosive mixture with a lower detonation velocity. High energy explosives led to extensive interfacial melting, preventing the production of consistent dissimilar welds. Unlike to the similar copper joints, the aluminium–copper welds presented very asymmetrical interfacial waves, rich in intermetallic phases and displaying a curled morphology. The interaction of the materials in dissimilar welding was found to be completely different depending on the positioning of each alloy in the joint, i.e. positioned as the flyer or as the baseplate.
- Microstructure and mechanical behaviour of aluminium-carbon steel and aluminium-stainless steel clads produced with an aluminium interlayerPublication . Carvalho, G. H. S. F. L.; Galvão, I.; Mendes, R.; Leal, R. M.; Loureiro, A.The influence of an interlayer on the microstructure and the mechanical behaviour of aluminium‑carbon steel and aluminium-stainless steel clads produced by explosive welding was studied. Different series of welds were produced both with and without an aluminium interlayer, testing different welding parameters. The combination of aluminium to carbon steel presented a better weldability than aluminium to stainless steel. For both couples, low-velocity welds presented the best microstructure and mechanical strength. The mechanical tests showed that the aluminium to carbon steel joining did not benefit from the use of the interlayer. A joint with good interfacial morphology and excellent tensile-shear properties was achieved by low-velocity direct welding, with the fracture occurring outside the joining region. For the aluminium to stainless steel couple, the use of the interlayer increased its weldability. However, the mechanical strength of the joint is restricted by the low strength of the interlayer. The presence of intermetallic compounds at the weld interface, does not, by itself, promote the poor-quality of the explosive weld. The way the interface accommodates and distributes these intermetallics dictates the weld's quality.
- Weldability of aluminium-copper in explosive weldingPublication . Carvalho, G. H. S. F. L.; Galvão, I.; Mendes, R.; Loureiro, A.; Leal, RuiA large number of aluminium-copper explosive welds were produced under different welding conditions to perform a broad analysis of the weldability of this combination. The influence of the explosive mixture and the relative positioning of the plates on the welding results were analysed. When the aluminium alloy is positioned as the flyer plate, continuous interfacial melting occurred under the low values of energy lost by the collision, and collision point velocity. This proved that the weldability of the aluminium-copper combination is higher when the copper is positioned as the flyer. A mismatch between the experimental results and the existing theories that define the requirements for achieving consistent welds was noticed. Especially for welds produced using the aluminium alloy as the flyer, the experiments proved to be more restrictive than the theories. These theories, despite being widely applied in dissimilar welding literature, present several limitations concerning aluminium-copper welding. New approaches considering the formation of intermetallic phases at the interface, the properties of both welded metals, and/or the difference in their properties should be developed